Stability and thermophysical properties of fly ash nanofluid for heat transfer applications

Improving the performance of heat transfer fluids is altogether significant. The best approach for improving the thermal conductivity is the addition of nanoparticles to the base fluid. In the present study, specific heat, dynamic viscosity, and thermal conductivity of water-based Indian coal fly ash stable nanofluid for 0.1% to 0.5% volume concentration in the temperature range of 30 to 60°C has been investigated. To evaluate an average particle diameter of 11.5 nm, the fly ash nanoparticles were characterized with scanning electron microscopy and dynamic light scattering. Using zeta potential, the stability of nanofluid in the presence of surfactant Triton X-100 was tested. Thermal conductivity and viscosity of fly ash nanofluid increased, while specific heat decreased as volume concentration increased. The effect of temperature on the fly ash nanofluid was directly proportional to its thermal conductivity and specific heat and inversely proportional to viscosity.     

Morphology,thermal and mechanical performance of epoxy/polysulfone composites improved by curing with two different aromatic diamines

Epoxy/polysufone (PSF) composites cured with 4,4'-diaminodiphenyl sulfone (DDS) and 4,4'-diaminodiphenyl methane (DDM) were fabricated, and the effect of dual curing reaction of diamines with epoxy on morphology, mechanical, and thermal performance was investigated. DSC results indicated that DDM was more reactive than DDS and the activation energy decreased with the rising of DDM content. Structures with small domain size at the early stage of phase separation were fixed by the fast epoxy-DDM reaction. When the DDM content was elevated to a high level, large dual structures were changed to fine bicontinuous structures, which was favorable to improve the mechanical property. The mechanical performance of epoxy composites was enhanced and the maximum values were achieved when the DDM/DDS ratio was located at 75/25 (PSF/DDS0.25-DDM0.75). The flexural and tensile strength relative to epoxy/DDM system were enhanced more than those relative to epoxy/DDS, while the increase in toughness was the opposite. TGA measurement showed that thermal stability of epoxy/PSF composites was improved because of the restricting effect of continuous PSF domains on thermal motion of epoxy. DMA analysis exhibited two relaxation peaks for PSF/DDS0.25-DDM0.75, which could be attributed to the formation of phase separated morphology and epoxy network with different cross-link density.     

含V型相交裂隙岩体的力学特性及破坏模式试验

为深入了解V型相交裂隙岩体试件的力学特性和裂纹演化规律,采用MTS815电液伺服控制试验机对含不同夹角V型相交裂隙岩体试件进行了常规单轴压缩试验,基于试验结果,详细分析了试件的应力-应变曲线、强度与变形特性、裂纹演化与破坏模式及能量耗散特征。研究结果表明:①裂隙试件的应力-应变曲线进入裂纹萌生与扩展阶段早于完整试件,在峰前出现了明显的应力降现象,在峰后破坏阶段,完整试件表现为应力-应变曲线的快速跌落,而裂隙试件呈现台阶状多阶段性跌落,甚至缓慢水平下降,体现出明显的延性破坏特征;②裂隙试件的峰值应力、弹性模量和峰值应变均有明显减小。峰值强度和弹性模量随裂隙夹角的增加呈先增大后减小的变化趋势。轴向峰值应变主要受裂隙夹角的影响,总体随夹角的增大呈线性减小的趋势;③裂隙的存在能够完全改变岩体试件的破坏模式,随着裂隙夹角的逐渐增加,裂隙试件破坏模式的演化过程为:台阶式张拉-剪切复合破坏(30°)→张拉-八字形剪切复合破坏(60°)→台阶式平行双斜面剪切破坏(90°)。当裂隙夹角为60°时,试件的裂纹演化和破坏模式体现出对加载方向近似的结构对称性特征;④相交裂隙试件单轴压缩破坏的弹性应变能、耗散能、总能量和能量耗散率均较完整试件有大幅度的减小。裂隙试件产生的裂纹数量越多,试件表面的脱落现象越明显,耗散能和能量耗散率也越大。拉-剪复合破坏比单纯剪切破坏要消耗更多的能量。试件的破坏特征和破坏模式能很好地反映试件的能量耗散特性。     

冷轧退火对FeMnCoCrAl高熵合金组织和力学性能的影响

使用真空电弧炉熔炼出(Fe₅₀Mn₃₀Co₁₀Cr₁₀)₉₄Al₆合金,利用冷轧及在不同温度对合金进行退火,以期望得到由多尺度再结晶晶粒构成的层状结构;并对不同退火温度的样品进行拉伸性能测试。利用扫描电镜和EBSD对合金组织形貌进行表征,采用X射线衍射方法研究其相组成。结果表明:合金在铸态和冷轧后相组成未发生变化,700 ℃退火得到较好的多尺度再结晶晶粒的层状结构,其屈服强度为487 MPa,抗拉强度为708 MPa,断后伸长率为39%,表现出良好的综合力学性能。     

等温退火对8030铝合金导线组织性能的影响

研究了不同等温退火工艺对8030铝合金导线组织及性能的影响。结果表明:等温退火前后合金均由α-Al基体和Al₆Fe相组成。在同一等温温度下,随着等温时间的延长组织逐渐趋于均匀化;同一等温时间下,随着等温温度的升高,组织趋于均匀化的时间缩短。经过等温退火处理后铝合金导线的导电率均有所提高,在470 ℃均匀化退火24 h后再经240 ℃等温4 h,合金导电率达到最高值57.21%IACS,比未经热处理试样的导电率提高了2.4%IACS。经过等温退火处理后铝合金导线的硬度及抗拉强度均有所降低,塑性大幅度提高。在470 ℃均匀化退火24 h后再经260 ℃等温8 h,合金的伸长率最高可达23.64%。热处理前后合金均为塑性断裂。     

多功能橡胶硫化活性剂ZH-73对全钢载重子午线轮胎胎面胶性能的影响

研究多功能橡胶硫化活性剂ZH-73对子午线轮胎胎面胶硫化特性、加工性能、物理性能和动态力学性能等的影响。结果表明:加入2份硫化活性剂ZH-73,混炼胶的门尼焦烧时间略缩短,t90延长,流动性提高,加工性能改善;硫化胶老化前后物理性能相当,60℃的损耗因子明显减小;成品轮胎耐久性能提高,滚动阻力系数降低。     

流量伺服阀作压力控制的非典型应用

文章提出并分析了一种用力反馈式流量伺服阀与手动节流阀配合使用,从而对负载进行压力控制的液压桥路。该桥路本质为C型半桥:伺服阀单腔输出,节流阀通过调节回油液阻来调节负载腔压力的起始点,伺服阀根据负载需求改变流量输出。整个压力控制回路为纯机械式控制,稳定可靠,精度可达0.1 bar。     

拉深筋对板材变形特征和力学性能的影响研究

采用实验方法将金属板材拉过不同尺寸的拉深筋镶块，分析了拉深筋高度、圆角半径以及过筋次数对板材变形特征的影响规律，研究了过筋产生的预应变对板材后续力学性能的影响规律。结果表明：板材流过拉深筋后，流动方向上发生均匀的拉伸变形；过筋产生的预应变随着拉深筋高度增大而增大，随着圆角半径增大而减小，随着过筋次数增加而近似线性增大；预应变越大，材料后续屈服强度和抗拉强度越高，但后续延伸率越小，总延伸率随着预应变增大表现出先减小后增大的趋势。     

氧化铈-二氧化硅介孔材料制备及对铜离子的吸附性能

采用共沉淀法和沉淀浸渍法制备了纳米氧化铈-二氧化硅（CeO₂-SiO₂）介孔材料吸附剂,主要考察了其对水中铜离子（Cu²⁺）的吸附行为。通过X射线衍射（XRD）、扫描电镜（SEM）和氮吸附（BET）等手段对合成的介孔材料进行了性能表征,并通过静态吸附实验分析了溶液pH、溶液初始金属离子质量浓度、吸附剂用量、吸附时间等条件对介孔材料吸附Cu²⁺性能的影响。结果表明：共沉淀法制备的纳米CeO₂-SiO₂介孔材料对Cu²⁺的去除效果较沉淀浸渍法要好;当溶液pH=7.0时CeO₂-SiO₂介孔材料对Cu²⁺的吸附效果最好,20 min时基本达到吸附平衡;溶液初始Cu²⁺浓度增大Cu²⁺去除率降低,Cu²⁺累计吸附量增大;随着吸附剂用量增加Cu²⁺去除率增大,当CeO₂-SiO₂吸附剂用量为0.15 g/L时对Cu²⁺的去除率趋于稳定;CeO₂-SiO₂吸附剂对不同金属离子吸附性能由大到小的顺序为Cu²⁺、Fe²⁺、Mn²⁺,该吸附过程均符合准二级动力学模型。     

纳米NiO掺杂Carbores'P对Al2O3-C耐火材料力学性能的影响

为提高低碳铝碳耐火材料的力学性能,以≤1 mm的棕刚玉、Si粉和Carbores’P为原料,外加纳米NiO为催化剂,制备Al2O3-C基质试样,利用XRD、SEM、激光拉曼光谱研究纳米NiO对Carbores’P炭化产物的影响。以棕刚玉(粒度为5~3、3-1、≤1 mm)、电熔白刚玉粉、Si粉、鳞片石墨、Carbores’P、纳米NiO为原料制备低碳Al2O3-C试样,研究纳米NiO掺杂Carbore’P对试样力学性能的影响。结果表明:1400℃埋碳热处理后,添加纳米NiO能提高基质的石墨化度,促进碳纳米管和SiC晶须的生成;正是由于它们的生成,提高了Al2O3-C试样的致密度、常温强度和断裂前的位移量,使试样韧性增强。